Wiring is laid in two ways - closed and open. In the first case, communications are masked, and the likelihood of their damage is minimal. Installation of open wiring is simpler, cheaper, and less time consuming, but you have to protect the cables from moisture, mechanical damage.
In this article, we will consider the existing methods for laying electrical wires, focus on the features of external installation and provide recommendations on how to choose the appropriate option.
What do electricians think about open wiring?
The disadvantages of open (external) wiring are much greater than that of hidden (internal).
Cables covered with plaster are not damaged, do not interfere with repair and are completely invisible. Open wiring is devoid of such advantages, and in the event of a short circuit it will light up more likely than hidden. An open installation method for wiring is often chosen for wooden houses.
In wooden houses, laying an electric cable in an open way is a necessary measure, because hidden cable management is difficult or even impossible
The open installation method still has some advantages:
- Simplified styling. When laying electric cables, you do not have to ditch the walls. This reduces labor costs, the amount of work. After installation, almost no construction debris remains.
- Cheaper. Here we are talking about saving on paying for electricians.
- Possibility to change cable routing. If plans for the future include redevelopment of wiring, then it is better to choose an open installation method.
When choosing an open method for laying electrical wires, it should be taken into account that they will have to be masked and protected from external influences. There is always the possibility of moisture or accidental damage.
When mounting boxes, sockets, switches, difficulties often arise. Before starting work, you need to carefully study the features of their installation or entrust the work to an electrician
If the house is residential, you need to weigh everything three times. It is advisable to consult an experienced electrician, and during installation it is necessary to take into account the increased risks and especially carefully monitor compliance with safety measures.
Features of external laying of electric cables
External installation is suitable if you need to lay electrical cables in the corners of the room, at the junction of the ceiling and walls, along the plinth.
Most often, difficulties arise when arranging open wiring in houses with suspended ceilings. Cables cannot be routed along such ceilings; you have to fix them on the walls.
One of the minuses of open wiring is its unpresentable appearance, however, it is ideal for a retro interior. The only caveat - you have to spend extra money on styling. It is expensive
If there are a lot of wires, it is better to lay them in the through channels. When developing the installation scheme, you need to carefully select the places where junction and junction boxes will be connected. Free access should be maintained for inspections and possible repairs of communications.
Open wiring methods
Initially, the only open installation method was to lay twisted electrical wires along the walls and ceiling. They were mounted on ceramic insulators.
In some houses built about a century ago, wiring is still laid this way. Relatively recently, a similar installation has again gained popularity. This is due to the fashion of antiquity.
If a hundred years ago, open wiring on ceramic insulators was considered the norm, now it’s antique styling. In the era of mass unification of things, furniture and interior items, unusual methods of decorating rooms are becoming especially popular, and this is one of them.
When designing rooms in retro style, there are often problems with finding materials. Some manufacturers produce ceramic insulators, sockets, antique switches, but such a luxury is very expensive.
Suitable materials for decorating retro wiring can be found not only in expensive stores. Often they are purchased from junk collectors, bought from owners of houses built at the beginning of the last century, and cables are made independently by twisting stranded copper wires.
Design fantasy knows no bounds. Often you can see interiors decorated with elements of different styles. One of the good options is a combination of retro and loft styling.
The interior fashion is changeable, so you should seriously consider whether you need to make wiring in retro style. It is better to choose a more popular and reliable option. Then, in case of repair, you won’t have to do electrical work again.
Image Gallery
Photo from
Retro twisted wire
Open Porcelain Insulators
Ceramic junction box
Wiring accessories made of ceramics
We offer you to consider in detail the popular methods for laying open wiring and choose the technology that is most suitable for your home.
Method 1 - mounting wires on brackets
To connect sockets and switches, choose electric wires with a cross section of 2.5 mm.sq., and for lighting devices - 1.5 mm.sq. Thicker cables are sometimes required. If the thickness of the wire is 1.5-6 mm.sq., they can simply be attached to the surfaces of walls and ceilings with brackets.
When buying cables, you should give preference to quality products. If the choice is made in favor of cheap wires, then non-combustible gaskets are mounted under them to reduce the risk of fire during a short circuit.
Their choice should be taken very carefully, because in future the functionality and safety of the home power grid will depend on them. We recommend that you look at information on how to calculate the wire cross section for home wiring.
The most commonly used bands are metal or asbestos. They are fixed so that the non-combustible gasket protrudes beyond the cable by at least 1 cm on each side. As for the material, it is better to choose metal, because asbestos is harmful to human health: its connection with cancer has been proven.
Sometimes, to ensure fire safety, they arrange a 1 cm gap between the power cable and the wall. This installation method is reminiscent of retro-style ceramic insulator wiring. It is used in wooden houses, in summer cottages, in non-residential premises
Brackets are a cheap and easy way to install wiring. Of the minuses - it is unsafe and ugly. If several cables are laid, they are striking and spoil the impression of the interior. In a residential building, it is better to lay the wires in the cable channels.
Method 2 - pipe laying features
Modern industry produces special electrical pipes. They can be made of metal or plastic, they protect well from fire, accidental mechanical damage and electric shock.
For installation, it is most convenient to use corrugated pipes. They are flexible, so that when mounting on the walls do not have to additionally level the surface. Corrugated pipe wiring is ideal for wooden log homes. It is convenient and looks much neater than individual wires.
Due to the dubious aesthetics of the corrugation, it is rarely used in residential buildings, but it is perfect for connecting cables from overhead power lines. Sometimes, in order to improve the appearance of open wiring inside the rooms, colored corrugated tubes are used.
When installing wires in a wooden house, the features of the building material are taken into account. Through the wooden walls, the wiring is laid using special metal bushings. They are needed to protect cables from being pinched if natural wood shrinks.
When calculating the diameter of the corrugation, they are guided by the total thickness of all the wires that will be laid in it. This number is multiplied by 2, because with a smaller cross-section of the pipe it will be difficult to lay cables in it.
To facilitate laying, corrugated tubes with a special probe (a wire with which the cables are pulled) are used. Attach the wires to the probe and pull them through the pipe, holding it tightly in your hands.
If you want to lay a relatively small piece of wire, it is quite possible to do without a probe, but for large segments it is better to use special devices.
The wiring device in the polymer corrugation is made in the following order:
Image Gallery
Photo from
For an open-circuit wiring device using a corrugated polymer pipe, we prepare material: corrugation with a margin of about 10% and mounting clips based on their installation after 30 cm
We cut the pipe into pieces of the required length without pulling. We take into account that one or two protrusions of the corrugation should start in the mounting boxes. First, we cut the corrugated channel with a construction knife, then we bite the wire available inside
We drill holes on the marked track to fix the clips, then install them by screwing on the marking with screws
Slightly pull out the probe in it, the metal wire, from the corrugation to attach the wire prepared for installation to it
With an awl, we pierce a point in the insulation of the wire, we introduce a probe into it, which we then bend with wire cutters. From the other edge of the corrugated pipe we pull the probe so that the wire fixed by it gets into the corrugated channel
In the mounting clips fixed according to the marking, we install the corrugated pipe with wires inserted into it, we fix it by snap
In order to firmly fix the corrugated channel in the clips, we supplement the fastening with a plastic screed
The "tails" of the plastic ties remaining after fastening are trimmed carefully with nippers
Stage 1: Preparing the material for the wiring device
Stage 2: Cut the corrugated pipe into pieces
Stage 3: Attaching the mounting clips
Stage 4: Preparing the corrugation for cable pulling
Step 5: Insert the wire into the polymer corrugation
Step 6: Snap the corrugated pipe into the clips
Step 7: Duplicate the mount with a plastic screed
Step 8: Trimming Surplus Plastic Fasteners
Corrugated electrical pipes are fixed to the walls with screws, dowels, nails or plastic clips. The distance between the attachment points is calculated depending on the diameter and, accordingly, the estimated weight. If the diameter of the corrugated pipe is 16 mm, then the fasteners are placed at a distance of 30–40 cm, and for pipes 32–40 mm this distance is already less than 20–30 cm.
Before starting electrical work, make up a diagram. It is important that the corrugated pipes do not intersect or intersect, as it violates security requirements and looks ugly
The clips are mounted on the walls, and then they simply insert a corrugated pipe into them. This method of fastening is convenient in that when dismantling it is enough to pull the pipe toward you and the clips can easily be detached.
Method 3 - laying in boxes
Rigid electrical ducts, cable channels, skirting boards are used for laying wires. These devices are made of metal or non-combustible plastic. Unlike corrugated pipes, rigid structures cannot be installed on uneven walls, as surface defects only become more visible.
There are many varieties of cable channels: one-, two-, three-section. They also vary in place of installation, purpose, size. On sale you can find models of any type - from perforated to flexible, angular or transparent. It is important to select products that are suitable for the specific operating conditions.
Boxes, channels, skirting boards are equipped with snap-on covers that can be easily removed, which is convenient for mounting additional wires. If you need to upgrade the wiring, the entire process will take several minutes.
There are other pluses:
- Design. Boxes, cable channels and skirting boards are available in different colors, which allows you to decorate the room. You can always choose the right option.
- Easy installation. Laying cables in boxes does not require much effort. The main thing is to properly secure the protective structures themselves.
- Convenient installation of sockets and switches. Outlets can be mounted on the box, and they will not spoil the overall look.
Installation work begins with the preparation of a drawing diagram with a scan of the walls. It is needed for the accurate calculation of the necessary materials, the number of fasteners, accessories.
To select a channel by size, you must first determine the cross-section and the number of cables. The finished plan must be accurate, without errors in measurements and calculations.
Wires are laid not only on smooth surfaces, but also in corners. Sometimes you need to equip the branches of the channels. For these purposes, use different types of accessories. When developing a project, you should calculate their number
Technology for mounting external wiring in cable channels:
- Project drafting. It is necessary to determine the number, types and location of sockets, switches, boxes and think over the cable laying scheme bypassing gas and water pipes, sewer systems.
- Selection of materials. After designing, you can proceed to the selection and purchase of materials. If you plan to lay several cables, you should choose a box with partitions. Accessories must match the channel in color and size. It makes sense to buy protective boxes with devices for installing outlets.
- Box fixing. Plastic constructions can crack if they are immediately fixed to the wall, so first make holes in the cases of the boxes, and only then screw them to the base. Cable channels are joined together, and excess material is cut off.
- Wiring. Cables are laid in the housing of the channels, closed with covers and snap them. It remains only to check the fixation of the covers - and the design is ready.
Electricians advise paying attention to the base material, as the choice of fasteners depends on this. So, on the wooden wall of the box is attached using ordinary screws. For brick, concrete and stone surfaces, dowels are used. And for panels, plates made of composite materials and plywood, it is better to choose butterfly fasteners.
So that you do not have to adjust the shape of the boxes in the external and internal corners, you can cut them off with the help of an ordinary joiner's miter box. Then the products will look neat, and the risk of material overruns due to defective work will significantly decrease
Each of the installation methods has its own advantages, and it rarely happens that one method is enough. Often it is necessary to combine cable channels with corrugated and / or metal pipes, fasteners on brackets.
The construction of electrical wiring using cable channels includes a number of standard steps:
Image Gallery
Photo from
Step 1: Installing the base of the cable channels
Step 2: Laying the wires in the installed base of the channels
Step 3: Install the base of the junction box
Step 4: Attaching the Front Panel of the Junction Box
Step 5: Mounting the box under the machines
Step 6: Preparing the Wiring for Connection
Step 7: Connecting Circuit Breakers
Step 8: Fixing the front of the machine unit
When developing a wiring project, you should take into account the layout of the room and the features of the cabling in each of the sections - whether it be a bedroom, a kitchen or a bathroom.
10 common mistakes electricians
An open way of laying electric cables is easier than a closed one, but still there are nuances that cannot be taken into account until there is a certain practice.
We offer an overview of typical mistakes made during wiring:
- Lack of circuit. Often, wiring is mounted according to the principle of the designer: first they make wiring in each room, and then the cables are combined. This dramatically reduces the reliability of the entire system.
- Material savings. Low-quality wires, devices and accessories are a direct and short way to a fire. It’s better to overpay for products of a reliable brand than to solve problems with short circuits and fires.
- Calculation of posting without stock. The cross-section of the cables and their number should be 20% more than the calculated one. Otherwise, unnecessary twists and the risk that the network will not withstand the load cannot be avoided.
- Connecting powerful appliances through a power outletinstead of using a separate cable from the shield. Even a power outlet does not solve this problem, because There is always a risk that the cable will not cope with a serious additional load.
- Connecting high and low voltage cables in one box. In this case, problems with the operation of equipment throughout the house are almost guaranteed.
- Extra twists. To connect the wires, it is better to use special terminals.
- Connection of cores from copper and aluminum. Contact points overheat, which can lead to problems. For the connection, it is worth using the terminals, but it is better to avoid aluminum wires and lay only copper ones.
- Neglect of safety. The rules of TB are written on the basis of the bitter experience of many unsuccessful electricians, and still there are still daredevils working under voltage.
- Incorrect junction box layout. They should be 20 cm below the ceiling. Otherwise, there is a risk of accidental damage. Boxes must be accessible for inspection and repair.
- Errors in installing the ground loop and connecting the RCD. These devices protect the mains, so their installation should be treated with particular care.
Novice electricians make other mistakes. We have listed only the most common.
It is important to remember that the installation of electrical wiring is fraught with many risks, so before starting work, you should carefully study the technology.
We selected useful video materials that will help to avoid frequent installation errors and to properly organize external wiring in the house.
Installation instructions for wiring in the cable channel:
Useful tips for installing outlets:
The main mistakes that are made when connecting an RCD:
In theory, the technology for arranging open wiring looks simple and straightforward. But when it comes to practice, many homeowners make a lot of mistakes.
Take on an independent installation only if you have the necessary knowledge for the development and implementation of the project. If not, don’t risk your life and entrust this work to electricians..
Are you well versed in the theory of open wiring and have practical experience in performing electrical work? Maybe you want to supplement our material with clarifications or useful recommendations? Write comments in the block under the article, share your experience with beginners - many users will be grateful to you.